Detection Systems DS7060 Uživatelský manuál stáhnout pdf (Strana 10)

4/98

Page 10 Copyright  1997-98 Detection Systems, Inc. DS7060-AUS Reference Guide

• Intrusion:

This is an output programmed to latch

with any Burg zone alarm, including invisible and

silent zones. It will remain latched until the system

is disarmed regardless of the restore setting for the

zone.

• On During Entry Pre-Alert:

This is an output

programmed to activate when a perimeter delayed

type zone is violated while the system is armed. It

will remain activated until the system is disarmed,

or until the entry delay time has expired.

• System Reset:

This is an output programmed to

activate only for 10 seconds after a PIN + [System

Reset] is entered at a keypad or if a fire zone with

verification activates. Output 1 turns on for 10

seconds, outputs 2 and 3 turn off for 10 seconds.

Outputs 2 and 3 are intended to be used to power

4-wire smoke detectors or any other device that

requires a power interruption to reset an alarm

condition.

• Armed:

This is an output programmed to activate

when the system is armed. It will remain activated

until the system is disarmed.

• Ground Start:

This is an output programmed to

activate for 3 seconds when the phone line is

seized. It is intended for use with ground start

phone systems that require a momentary short to

ground to obtain a dial tone. Connect a separate 12

VDC, DPDT relay. Connect both relay commons to

ground, and connect the N/O of each contact to

terminal positions 23 and 26 (one to terminal 23,

one to 26) of the DS7060. Connect one side of the

relay coil to the selected Programmable Output and

the other side of the coil to 12 volts (Terminal 5) (if

PO1 or PO2 is used), or to any Panel Common

terminal if PO3 is used. Not intended for UL Listed

systems. Not for use with phone line monitors.

• Ready to Arm (System Status):

This is an output

programmed to follow the “Status” light of the

keypad. It will activate when the system is ready to

arm with no zones violated.

• Follow Burg Alarm:

This is an output programmed

to activate when a zone is in an alarm condition. It

will remain activated until the system is disarmed or

the bell cutoff time expires. This output is intended

to activate bells and sirens. This will not activate

from Silent or Invisible zones.

• Follow Fire Alarm:

This is an output programmed

to activate when a zone is in an fire alarm condition.

It will remain activated until the system is disarmed

(or silenced using PIN + [Off] ) or the bell cutoff time

expires. This output is intended to activate bells and

sirens. This will not activate from Silent or Invisible

zones.

• Follow Burg and Fire Alarm:

This programs an

output to activate when any zone goes into alarm

condition.

• Follow Keypad Sounder:

This is an output

programmed to follow the keypad sounder. It

activates during the entry pre-alert . It does not

follow momentary keypad beeps such as

keystrokes.

• Duress:

This output activates when the duress

code is used to disarm the system.

Note:

If the Duress code is used to activate a

Programmable Output, entering any valid PIN +

[OFF} will deactivate the Programmable Output.

• Trouble:

This output activates when a trouble

condition is present.

• Off During Battery Test:

This output turns Off

(deactivates) for 2 seconds during a manual or

automatic battery test.

• Partial Armed:

This output activates whenever the

system is armed with one or more zones bypassed.

This includes manual bypasses, custom arming and

force arming.

• Follow Burg Alarm 20 Second Delay:

This output

will be delayed for 20 seconds after a zone enters

an alarm condition. It will remain activated until the

system is disarmed or the bell timeout expires.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 23 24

Komentáře k této Příručce

Žádné komentáře

Detection Systems DS7060 Uživatelský manuál Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Detection Systems DS7060